luci-app-easymesh/root/easymesh/easymesh.sh

#!/bin/bash

clear_old_networks() {
    # Get the mesh name from UCI config
    MESH_NAME=$(uci -q get easymesh.config.mesh_id)

    # Get all the radios and go through them one by one to remove old networks and interfaces with the same mesh name
    for CURRENT_RADIO in $(uci -X show wireless | grep wifi-device | awk -F'[.=]' '{print $2}'); do
        echo "Clearing old networks for radio: $CURRENT_RADIO"

        # Use awk to parse the 'uci show wireless' output and find the matching section
        matched_section=$(uci show wireless | awk -F. -v radio="$CURRENT_RADIO" -v ssid="$MESH_NAME" '
        $0 ~ /^wireless\.wifinet[0-9]+\.device=/ && $3 ~ radio { device_section=$2 }
        $0 ~ /^wireless\.wifinet[0-9]+\.ssid=/ && $3 ~ ssid && device_section == $2 { print $2; exit }
        ')

        # Check if a matching section was found
        if [ -n "$matched_section" ]; then
            echo "The matching wireless interface section is: $matched_section - deleting it"
            uci delete wireless.$matched_section
        fi

        # Find and delete existing mesh network interfaces with the specified MESH_NAME on the current radio
        EXISTING_MESH=$(uci show wireless | grep -w "mesh_id='$MESH_NAME'" | grep ".$CURRENT_RADIO." | cut -d'.' -f1-2)
        for section in $EXISTING_MESH; do
            uci delete $section
            echo "The matching wireless interface section is: $section - deleting it"
        done

        # Commit changes to wireless
        uci commit
    done
}

create_bat0() {
    # Check if bat0 already exists
    if uci -q get network.bat0 >/dev/null; then
        echo "bat0 interface already exists."
    else
        uci set network.bat0=interface
        uci set network.bat0.proto='batadv'
        uci set network.bat0.routing_algo='BATMAN_IV'
        uci set network.bat0.aggregated_ogms='1'
        uci set network.bat0.ap_isolation='0'
        uci set network.bat0.bonding='1'
        uci set network.bat0.bridge_loop_avoidance='1'
        uci set network.bat0.distributed_arp_table='1'
        uci set network.bat0.fragmentation='1'
        uci set network.bat0.hop_penalty='30'
        uci set network.bat0.isolation_mark='0x00000000/0x00000000'
        uci set network.bat0.log_level='0'
        uci set network.bat0.multicast_fanout='16'
        uci set network.bat0.multicast_mode='1'
        uci set network.bat0.network_coding='0'
        uci set network.bat0.orig_interval='1000'
        echo "bat0 interface has been created."

        # Set the bat0 role
        BAT_ROLE=$(uci -q get easymesh.config.role)
        if [ "${BAT_ROLE}" == "server" ]; then
            uci set network.bat0.gw_mode='server'
        elif [ "${BAT_ROLE}" == "client" ]; then
            uci set network.bat0.gw_mode='client'
        else
            uci set network.bat0.gw_mode='off'
        fi

        # Get the current list of ports for the 'br-lan' interface
        LAN_PORTS=$(uci -q get network.@device[0].ports)
        # Check if 'bat0' is already in the list of ports for 'br-lan'
        if echo "$LAN_PORTS" | grep -q 'bat0'; then
            uci del_list network.@device[0].ports='bat0'
            echo "Old bat0 interface deleted from lan network."
        fi

        # Add 'bat0' to the list of ports for 'br-lan'
        uci add_list network.@device[0].ports='bat0'
        echo "bat0 has been added to the lan network."

        uci commit network
    fi
}

find_radios() {
    # Get the radio to be used for mesh from the config
    AP_RADIO=$(uci -q get easymesh.config.apRadio)

    # Check if AP_RADIO is empty, if so exit
    if [ -z "$AP_RADIO" ]; then
        echo "No radio specified in the config, exiting."
        exit 1
    fi

    # Check to make sure if "all" is passed or a single radio
    if [ "$AP_RADIO" == "all" ]; then
        # Get the list of wifi devices
        WIFI_RADIOS=$(uci -X show wireless | awk -F'[.=]' '/wifi-device/ {print $2}' | tr '\n' ' ')
    else
        # Set the radio to the one passed in the config
        WIFI_RADIOS=$AP_RADIO
    fi
}

process_radios() {
    # Check if WIFI_RADIOS contains more than one radio
    if [[ $WIFI_RADIOS =~ [[:space:]] ]]; then
        # Loop through all the radios and set them up
        for radio in $WIFI_RADIOS; do
            echo "Multiple Radio Setup, Current Radio: $radio"
            setup_mesh_radio $radio
        done
    else
        echo "Calling Single Radio Setup: $WIFI_RADIOS"
        setup_mesh_radio $WIFI_RADIOS
    fi
}

# This is called from the process_radios function and is passed the radio to be used for mesh
setup_mesh_radio() {
    CURRENT_RADIO=$1
    echo "Setting up radio: $CURRENT_RADIO"

    # Get the mesh name from UCI config
    MESH_NAME=$(uci -q get easymesh.config.mesh_id)

    # Commit changes to wireless
    uci commit wireless

    uci set network.nwi_mesh_$CURRENT_RADIO=interface
    uci set network.nwi_mesh_$CURRENT_RADIO.proto='batadv_hardif'
    uci set network.nwi_mesh_$CURRENT_RADIO.master='bat0'
    uci set network.nwi_mesh_$CURRENT_RADIO.device='bat0'
    uci set network.nwi_mesh_$CURRENT_RADIO.mtu='1536'

    uci set wireless.mesh_$CURRENT_RADIO=wifi-iface
    uci set wireless.mesh_$CURRENT_RADIO.device=$CURRENT_RADIO
    uci set wireless.mesh_$CURRENT_RADIO.ifname=mesh_$CURRENT_RADIO
    uci set wireless.mesh_$CURRENT_RADIO.network=nwi_mesh_$CURRENT_RADIO
    uci set wireless.mesh_$CURRENT_RADIO.mode='mesh'
    uci set wireless.mesh_$CURRENT_RADIO.mesh_id=$MESH_NAME
    uci set wireless.mesh_$CURRENT_RADIO.mesh_fwding='0'
    uci set wireless.mesh_$CURRENT_RADIO.mesh_rssi_threshold='0'
    uci set wireless.mesh_$CURRENT_RADIO.mesh_ttl='1'
    uci set wireless.mesh_$CURRENT_RADIO.mcast_rate='24000'
    uci set wireless.mesh_$CURRENT_RADIO.disabled='0'

    uci commit wireless

    # Extact the radio number from the radio name
    RADIO_NUM="${CURRENT_RADIO#radio}"

    # Get the mobility domain from the config
    MOBILITY_DOMAIN=$(uci -q get easymesh.config.mobility_domain)

    # If mobility domain is empty, set it to a random 4 digit hex number, then set it in the config
    if [ -z "$MOBILITY_DOMAIN" ]; then
        MOBILITY_DOMAIN=$(hexdump -n 2 -e '2/1 "%02x"' /dev/urandom)
        uci set easymesh.config.mobility_domain=$MOBILITY_DOMAIN
        uci commit easymesh
    fi

    # Get the encryption enabled from the config
    ENCRYPTION_ENABLED=$(uci -q get easymesh.config.encryption)

    # Setup the interface for the mesh network
    uci set wireless.mesh_$CURRENT_RADIO.disabled='0'
    uci set wireless.wifinet$RADIO_NUM=wifi-iface
    uci set wireless.wifinet$RADIO_NUM.device=$CURRENT_RADIO
    uci set wireless.wifinet$RADIO_NUM.mode='ap'
    uci set wireless.wifinet$RADIO_NUM.ssid=$MESH_NAME
    uci set wireless.wifinet$RADIO_NUM.ieee80211r='1'
    uci set wireless.wifinet$RADIO_NUM.mobility_domain=$MOBILITY_DOMAIN
    uci set wireless.wifinet$RADIO_NUM.ft_over_ds='0'
    uci set wireless.wifinet$RADIO_NUM.ft_psk_generate_local='0'
    uci set wireless.wifinet$RADIO_NUM.network='lan'
    uci set wireless.wifinet$RADIO_NUM.disabled=0

    # Get the encryption key from the config
    NETWORK_KEY=$(uci -q get easymesh.config.key)

    # Check if encryption is enabled and if the key is not empty
    if [ "$ENCRYPTION_ENABLED" = 1 ] && [ ! -z $NETWORK_KEY ]; then
        uci set wireless.mesh_$CURRENT_RADIO.encryption='sae'
        uci set wireless.mesh_$CURRENT_RADIO.key=$NETWORK_KEY
        uci set wireless.wifinet$RADIO_NUM.encryption='sae-mixed'
        uci set wireless.wifinet$RADIO_NUM.key=$NETWORK_KEY
    else
        uci set wireless.mesh_$CURRENT_RADIO.encryption='none'
        uci set wireless.wifinet$RADIO_NUM.encryption='none' 
        [ -z $NETWORK_KEY ] && echo "Encryption key is empty, so encryption was disabled."
    fi

    # Commit our block of changes to wireless
    uci commit wireless

    # Check if we need to setup kvr
    ENABLE_KVR=$(uci -q get easymesh.config.kvr)

    if [ "$ENABLE_KVR" = 1 ]; then
        uci set wireless.wifinet$RADIO_NUM.ieee80211k='1'
        uci set wireless.wifinet$RADIO_NUM.rrm_neighbor_report='1'
        uci set wireless.wifinet$RADIO_NUM.rrm_beacon_report='1'
        uci set wireless.wifinet$RADIO_NUM.ieee80211v='1'
        uci set wireless.wifinet$RADIO_NUM.bss_transition='1'
        uci set wireless.wifinet$RADIO_NUM.ieee80211r='1'
        uci set wireless.wifinet$RADIO_NUM.ft_over_ds='1'
        uci set wireless.wifinet$RADIO_NUM.ft_psk_generate_local='1'
        uci commit wireless
    else
        uci -q delete wireless.wifinet$RADIO_NUM.ieee80211k
        uci -q delete wireless.wifinet$RADIO_NUM.ieee80211v
        uci -q delete wireless.wifinet$RADIO_NUM.ieee80211r
        uci commit wireless
    fi

    # Check if we need to setup iapp
    ENABLE_IAPP=$(uci -q get easymesh.config.iapp)

    if [ "$ENABLE_IAPP" = 1 ]; then
        # Get the LAN interface name
        LAN_NAME=$(uci -q get network.@device[0].name)
        # If LAN_NAME is not empty, set the iapp interface
        if [ ! -z "$LAN_NAME" ]; then
            uci set wireless.wifinet$RADIO_NUM.iapp_interface="$LAN_NAME"
            uci commit wireless
        fi 
    else
        uci -q delete wireless.wifinet$RADIO_NUM.iapp_interface
        uci commit wireless
    fi

    # If KVR is enabled, setup DAWN
    if [ "$ENABLE_KVR" = 1 ]; then
        RSSI=$(uci -q get easymesh.config.rssi_val)
        LOW_RSSI=$(uci -q get easymesh.config.low_rssi_val)  
        uci set dawn.@metric[0].rssi_val=$RSSI
        uci set dawn.@metric[0].low_rssi_val=$LOW_RSSI
        uci commit dawn
        /etc/init.d/dawn enable && /etc/init.d/dawn start
    else
        /etc/init.d/dawn stop && /etc/init.d/dawn disable
    fi

    # Commit our block of changes to the configs
    uci commit
}

restart_and_reload() {
    # Enable all the radios and commit the changes at once
    for radio in $(uci -X show wireless | grep wifi-device | awk -F'[.=]' '{print $2}'); do
        echo "Enabling $radio..."
        uci set wireless.$radio.disabled=0
    done
    uci commit
    echo "All radios enabled."

    # Apply the wireless configuration changes
    wifi reload
    echo "Wireless interfaces reloaded."

    # Apply network configuration changes
    # Note: Only use reload_config if you have made changes to the network config
    # and need to apply them. Otherwise, you can skip this step.
    reload_config
    echo "Network configuration reloaded."

    /etc/init.d/network reload
    /etc/init.d/network restart
}

disable_easymesh() {
    # Delete the bat0 interface
    if [ "$(uci -q get network.bat0)" = "interface" ]; then
        uci del network.bat0
    fi

    # Get the current list of ports for the 'br-lan' interface
    LAN_PORTS=$(uci -q get network.@device[0].ports)
    # Check if 'bat0' is already in the list of ports for 'br-lan'
    if echo "$LAN_PORTS" | grep -q 'bat0'; then
        uci del_list network.@device[0].ports='bat0'
        echo "Old bat0 interface deleted from lan network."
    fi

    # Get the list of wifi devices
    WIFI_RADIOS=$(uci -X show wireless | awk -F'[.=]' '/wifi-device/ {print $2}' | tr '\n' ' ')

    # Loop through all the radios and delete the network interfaces
    for CURRENT_RADIO in $WIFI_RADIOS; do
        echo "Handling removal of mesh networks for: $CURRENT_RADIO"
        if [ "$(uci -q get network.nwi_mesh_$CURRENT_RADIO)" = "interface" ]; then
            uci del network.nwi_mesh_$CURRENT_RADIO
            uci commit network
        fi
    done

    uci commit

    reload_config
    echo "Network configuration reloaded."

    /etc/init.d/network reload
    /etc/init.d/network restart
}

set_apmode() {
    AP_MODE=$(uci -q get easymesh.config.ap_mode)
    if [ "$AP_MODE" = 1 ]; then
        # Set a flag to indicate that we are in AP mode
        # When we go to disable easymesh, we will check this flag and if it was set we restore settings
        uci set easymesh.config.ap_mode_enabled=1

        # Backup our configs
        rm /etc/config/*.meshbak
        cp /etc/config/wireless /etc/config/wireless.meshbak
        cp /etc/config/network /etc/config/network.meshbak
        cp /etc/config/dhcp /etc/config/dhcp.meshbak

        # Generate a random IP in the same subnet for fun
        # ip_base=$(echo "$dns" | cut -d'.' -f1-3)  # Get the first three octets of the DNS IP
        # last_octet=$((RANDOM % 254 + 1))  # Generate a random value for the last octet between 1 and 254
        # nodeip="${ip_base}.${last_octet}"  # Concatenate the base IP with the new last octet

        # Disabling and stopping services not needed
        for service in firewall dnsmasq odhcpd; do
            if /etc/init.d/$service enabled; then
                echo "Disabling and stopping $service..."
                /etc/init.d/$service disable
                /etc/init.d/$service stop
            else
                echo "$service is not enabled, skipping..."
            fi
        done

        # Set LAN interface to DHCP client
        uci del network.lan.ipaddr
        uci del network.lan.netmask
        uci set network.lan.proto='dhcp'
        uci del network.wan
        uci del network.wan6

        # Fix firewall to be disabled
        uci del firewall.lan.network
        uci del firewall.wan.network

        # Fix dhcp to be disabled
        uci set dhcp.lan.ignore='1'
        uci del dhcp.wan

        # Fix this for proper variable name
        HOSTNAME=$(uci -q get easymesh.config.gateway)
        # Set netmask and gateway (assuming $netmask and $dns didn't break more stuff)
        uci set system.@system[0].hostname=$HOSTNAME

        # Retrieve the list of ports for network.@device[0]
        LAN_PORTS=$(uci get network.@device[0].ports)

        # Check if 'wan' is already in the list of ports
        if echo "$LAN_PORTS" | grep -q -w 'wan'; then
            echo "'wan' is already in the list of ports for lan."
        else
            echo "'wan' is not in the list. Adding it to lan ports..."
            uci add_list network.@device[0].ports='wan'
        fi

        # Find all radios we are using in our setup
        find_radios

        #### COME BACK TO THIS ####
        # # Check if WIFI_RADIOS contains more than one radio
        # if [[ $WIFI_RADIOS =~ [[:space:]] ]]; then
        #     # Loop through all the radios add nwimesh to the that network
        #     for cur_radio in $WIFI_RADIOS; do
        #         echo "Multiple Radio Setup, Current Radio: $radio"
        #         # Extact the radio number from the radio name
        #         wifi_num="${cur_radio#radio}"
        #         uci set wireless.wifinet${wifi_num}.network="lan nwi_mesh_${cur_radio}"
        #     done
        # else
        #     echo "Calling Single Radio Setup: $WIFI_RADIOS"
        #     # Extact the radio number from the radio name
        #     wifi_num="${WIFI_RADIOS#radio}"
        #     uci set wireless.wifinet${wifi_num}.network="lan nwi_mesh_${WIFI_RADIOS}"
        # fi

        uci commit
        # Tell openwrt to reload the configs
        reload_config
    else
        # Set a flag to indicate that we are in AP mode
        uci set easymesh.config.ap_mode_enabled=0

        # Restore our configs
        [ -f /etc/config/wireless.meshbak ] && {
            mv /etc/config/wireless /etc/config/wireless.dumbap
            cp /etc/config/wireless.meshbak /etc/config/wireless
        }
        [ -f /etc/config/network.meshbak ] && {
            mv /etc/config/network /etc/config/network.dumbap
            cp /etc/config/network.meshbak /etc/config/network
        }
        [ -f /etc/config/dhcp.meshbak ] && {
            mv /etc/config/dhcp /etc/config/dhcp.dumbap
            cp /etc/config/dhcp.meshbak /etc/config/dhcp
        }

        # Enable and start services not needed
        for service in firewall dnsmasq odhcpd; do
            if /etc/init.d/$service disabled; then
                echo "Enabling and starting $service..."
                /etc/init.d/$service enable
                /etc/init.d/$service start
            else
                echo "$service is not disabled, skipping..."
            fi
        done

        reload_config
        /etc/init.d/network reload
    fi
}

# ENABLED=$(uci -q get easymesh.config.enabled)
# if [ "$ENABLED" = 1 ]; then
#     clear_old_networks
#     create_bat0
#     find_radios
#     process_radios
#     restart_and_reload
# else
#     clear_old_networks
#     disable_easymesh
# fi

# We accept the parameters: start, stop and apmode
# start: Enables easymesh
# stop: Disables easymesh
# apmode: Sets the device to AP mode
if [ "$1" = "start" ]; then
    clear_old_networks
    create_bat0
    find_radios
    process_radios
    restart_and_reload
elif [ "$1" = "stop" ]; then
    clear_old_networks
    disable_easymesh
# elif [ "$1" = "apmode" ]; then
#     set_apmode
else
    echo "Invalid parameter passed."
fi