@ -1,38 +1,234 @@
#!/bin/bash #!/bin/bash
clear_old_networks( ) {
# Dumb AP Mode Block
# Get the mesh name from UCI config
set_apmode( ) {
MESH_NAME = $( uci -q get easymesh.config.mesh_id)
# Backup our configs
rm /etc/config/*.meshbak
cp /etc/config/wireless /etc/config/wireless.meshbak
cp /etc/config/network /etc/config/network.meshbak
cp /etc/config/dhcp /etc/config/dhcp.meshbak
cp /etc/config/system /etc/config/system.meshbak
cp /etc/config/firewall /etc/config/firewall.meshbak
uci set easymesh.config.ap_mode_enabled= 1
# Disabling and stopping services not needed
for service in firewall dnsmasq odhcpd; do
if /etc/init.d/$service enabled; then
echo " Disabling and stopping $service ... "
/etc/init.d/$service disable >/dev/null 2>& 1
/etc/init.d/$service stop >/dev/null 2>& 1
else
echo " $service is not enabled, skipping... "
fi
done
if [ $( uci -q get easymesh.config.ipmode) = = "static" ] ; then
# Set static IP
uci set network.lan.proto= 'static'
uci set network.lan.ipaddr= $( uci -q get easymesh.config.ipaddr)
uci set network.lan.netmask= $( uci -q get easymesh.config.netmask)
uci set network.lan.gateway= $( uci -q get easymesh.config.gateway)
uci set network.lan.dns= $( uci -q get easymesh.config.dns)
else
# Set LAN interface to DHCP client
uci del network.lan.ipaddr
uci del network.lan.netmask
uci set network.lan.proto= 'dhcp'
fi
# Get all the radios and go through them one by one to remove old networks and interfaces with the same mesh name
# Delete wan interfaces
for CURRENT_RADIO in $( uci -X show wireless | grep wifi-device | awk -F'[.=]' '{print $2}' ) ; do
uci del network.wan
echo " Clearing old networks for radio: $CURRENT_RADIO "
uci del network.wan6
# Use awk to parse the 'uci show wireless' output and find the matching section
# Set firewall disabled
matched_section = $( uci show wireless | awk -F. -v radio = " $CURRENT_RADIO " -v ssid = " $MESH_NAME " '
uci del firewall.lan.network
$0 ~ /^wireless\. wifinet[ 0-9] +\. device = / && $3 ~ radio { device_section = $2 }
uci del firewall.wan.network
$0 ~ /^wireless\. wifinet[ 0-9] +\. ssid = / && $3 ~ ssid && device_section = = $2 { print $2 ; exit }
' )
# Check if a matching section was found
# Just in case, set lan to be ignored by dhcp
if [ -n " $matched_section " ] ; then
uci set dhcp.lan.ignore= '1'
echo " The matching wireless interface section is: $matched_section - deleting it "
uci del dhcp.wan
uci delete wireless.$matched_section
fi
# Fix this for proper variable name
HOSTNAME = $( uci -q get easymesh.config.hostname)
# Set netmask and gateway (assuming $netmask and $dns didn't break more stuff)
uci set system.@system[ 0] .hostname= $HOSTNAME
# Find and delete existing mesh network interfaces with the specified MESH_NAME on the current radio
# Retrieve the list of ports for network.@device[0]
EXISTING_MESH = $( uci show wireless | grep -w " mesh_id=' $MESH_NAME ' " | grep " . $CURRENT_RADIO . " | cut -d'.' -f1-2)
LAN_PORTS = $( uci get network.@device[ 0] .ports)
for section in $EXISTING_MESH ; do
uci delete $section
# Check if 'wan' is already in the list of ports
echo " The matching wireless interface section is: $section - deleting it "
if echo " $LAN_PORTS " | grep -q -w 'wan' ; then
echo "'wan' is already in the list of ports for lan."
else
echo "'wan' is not in the list. Adding it to lan ports..."
uci add_list network.@device[ 0] .ports= 'wan'
fi
# Get the radio to be used for mesh from the config
AP_RADIO = $( uci -q get easymesh.config.apRadio)
# Our config set mesh_id that we are looking for
MESH_ID = $( uci -q get easymesh.config.mesh_id)
# Check if MESH_NAME and AP_RADIO are set, if so find set our network
if [ ! -z " $AP_RADIO " ] && [ ! -z " $MESH_ID " ] ; then
# Loop through the radios and update the network settings
for radio in $AP_RADIO ; do
# Get the number from the radio name
radio_num = " ${ radio #radio } "
echo " Checking wireless networks on radio ${ radio_num } for ssid ' $MESH_ID ' "
# Loop through all the wireless interfaces associated with the current radio
uci show wireless | grep " wireless\.wifinet ${ radio_num } " | grep '\.ssid=' | while read -r ssid_line; do
# Extract the interface identifier
wifinet = $( echo " $ssid_line " | cut -d'.' -f2)
# Extract the ssid value
interface_ssid = $( echo " $ssid_line " | cut -d'=' -f2 | tr -d "'" )
if [ " $interface_ssid " = " $MESH_ID " ] ; then
echo " Found target SSID ' $MESH_ID ' on wireless wifinet ${ wifinet } on radio ${ radio } "
# Get the current network setting for this wifinet
current_network = $( uci get " wireless. ${ wifinet } .network " )
echo " Current network setting for ${ wifinet } : ${ current_network } "
# Check if 'private_router_batman' is part of the current network setting
if echo " $current_network " | grep -qv 'private_router_batman' ; then
# 'private_router_batman' is not in the network setting, so we add it
new_network = " ${ current_network } private_router_batman "
uci set " wireless. ${ wifinet } .network= ${ new_network } "
echo " Added 'private_router_batman' to the network setting for ${ wifinet } . "
uci commit wireless
else
echo " 'private_router_batman' is already in the network setting for ${ wifinet } . "
fi
else
echo " SSID ' $interface_ssid ' on wireless wifinet ${ wifinet } does not match target SSID ' $MESH_ID '. Skipping... "
fi
done
done
done
fi
# Commit changes to wireless
# Commit changes to make sure the wireless configuration is updated
uci commit
uci commit
done
# Restart wireless
wifi reload
# Tell openwrt to reload the configs
reload_config
/etc/init.d/network reload
} }
create_bat0( ) {
disable_apmode( ) {
# Config Count Must Match 5
local CONFIG_COUNT = 0
# Check our configs exist, then restore them
[ -f /etc/config/wireless.meshbak ] && {
CONFIG_COUNT = $(( CONFIG_COUNT+1))
}
[ -f /etc/config/network.meshbak ] && {
CONFIG_COUNT = $(( CONFIG_COUNT+1))
}
[ -f /etc/config/dhcp.meshbak ] && {
CONFIG_COUNT = $(( CONFIG_COUNT+1))
}
[ -f /etc/config/system.meshbak ] && {
CONFIG_COUNT = $(( CONFIG_COUNT+1))
}
[ -f /etc/config/firewall.meshbak ] && {
CONFIG_COUNT = $(( CONFIG_COUNT+1))
}
# Check if we have 5 configs to restore
if [ $CONFIG_COUNT -eq 5 ] ; then
echo "Restoring configs from backup..."
echo "Existing configs will be moved to /etc/config/*.dumbap for reference."
rm /etc/config/*.dumbap
mv /etc/config/dhcp /etc/config/dhcp.dumbap
mv /etc/config/network /etc/config/network.dumbap
mv /etc/config/wireless /etc/config/wireless.dumbap
mv /etc/config/system /etc/config/system.dumbap
mv /etc/config/firewall /etc/config/firewall.dumbap
mv /etc/config/dhcp.meshbak /etc/config/dhcp
mv /etc/config/network.meshbak /etc/config/network
mv /etc/config/wireless.meshbak /etc/config/wireless
mv /etc/config/system.meshbak /etc/config/system
mv /etc/config/firewall.meshbak /etc/config/firewall
# Enable and start services not needed
for service in firewall dnsmasq odhcpd; do
if /etc/init.d/$service disabled; then
echo " Enabling and starting $service ... "
/etc/init.d/$service enable
/etc/init.d/$service start
else
echo " $service is not disabled, skipping... "
fi
done
# Reload all the system configs
reload_config
/etc/init.d/network reload
wifi reload
else
echo "Unable to restore configs as none were found."
fi
}
clear_by_mesh_id( ) {
# Passed mesh_id to clear, allows us to multipurpose this function
MESH_ID_TO_CLEAR = $1
# Get the radio to be used for mesh from the config
AP_RADIO = $( uci -q get easymesh.config.apRadio)
# Check if MESH_NAME is not empty
if [ -z " $MESH_ID_TO_CLEAR " ] ; then
echo "No mesh_id passed to remove from wireless."
return ;
fi
# Get the output from uci show wireless
uci_output = $( uci show wireless)
# Find the mesh network with the matching mesh_id and delete it
mesh_id = $( echo " $uci_output " | grep -o " wireless\.mesh_radio[0-9]*\.mesh_id=' $MESH_ID_TO_CLEAR ' " )
if [ ! -z " $mesh_id " ] ; then
# Extract the number from the interface name
mesh_radio = $( echo " $mesh_id " | grep -o "radio[0-9]*" )
# Loop through radios and delete the mesh networks
for radio in $AP_RADIO ; do
# Delete the network
uci del wireless.mesh_$radio
echo " Deleted mesh network with mesh_id ' $MESH_ID_TO_CLEAR ' on $radio "
done
fi
# Find the wireless network with the matching ssid and delete it
ssid = $( echo " $uci_output " | grep -o " wireless\.wifinet[0-9]*\.ssid=' $MESH_ID_TO_CLEAR ' " )
if [ ! -z " $ssid " ] ; then
# Loop through radios and delete the wireless networks
for radio in $AP_RADIO ; do
# Get the number from the radio name
radio_num = " ${ radio #radio } "
# Delete the network
uci del wireless.wifinet$radio_num
echo " Deleted wireless network with ssid ' $MESH_ID_TO_CLEAR ' on radio $radio_num "
done
fi
# Commit changes to make sure the wireless configuration is updated
uci commit wireless
# Restart wireless to apply changes
wifi reload
echo "Wireless interfaces reloaded."
}
create_batman_network( ) {
# Check if bat0 already exists
# Check if bat0 already exists
if uci -q get network.bat0 >/dev/null; then
if uci -q get network.bat0 >/dev/null; then
echo "bat0 interface already exists."
echo "bat0 interface already exists."
@ -73,15 +269,28 @@ create_bat0() {
echo "Old bat0 interface deleted from lan network."
echo "Old bat0 interface deleted from lan network."
fi
fi
# Add 'bat0' to the list of ports for 'br-lan'
uci commit network
uci add_list network.@device[ 0] .ports= 'bat0'
fi
echo "bat0 has been added to the lan network."
# Check if network.private_router_batman already exists
if uci -q get network.private_router_batman >/dev/null; then
echo "network.private_router_batman interface already exists."
else
# Get the LAN bridge name
LAN_NAME = $( uci -q get network.@device[ 0] .name)
# Setup our Private Router Batman Interface
uci set network.private_router_batman= interface
uci set network.private_router_batman.proto= 'batadv_hardif'
uci set network.private_router_batman.master= 'bat0'
uci set network.private_router_batman.device= " $LAN_NAME "
uci set network.private_router_batman.mtu= '1536'
uci commit network
uci commit network
fi
fi
} }
find_radios( ) {
process _radios( ) {
# Get the radio to be used for mesh from the config
# Get the radio to be used for mesh from the config
AP_RADIO = $( uci -q get easymesh.config.apRadio)
AP_RADIO = $( uci -q get easymesh.config.apRadio)
@ -91,28 +300,11 @@ find_radios() {
exit 1
exit 1
fi
fi
# Check to make sure if "all" is passed or a single radio
# Loop through the selected radios
if [ " $AP_RADIO " = = "all" ] ; then
for CURRENT_RADIO in $AP_RADIO ; do
# Get the list of wifi devices
echo " Setting up mesh networks for: $CURRENT_RADIO "
WIFI_RADIOS = $( uci -X show wireless | awk -F'[.=]' '/wifi-device/ {print $2}' | tr '\n' ' ' )
setup_mesh_radio $CURRENT_RADIO
else
done
# Set the radio to the one passed in the config
WIFI_RADIOS = $AP_RADIO
fi
}
process_radios( ) {
# Check if WIFI_RADIOS contains more than one radio
if [ [ $WIFI_RADIOS = ~ [ [ :space:] ] ] ] ; then
# Loop through all the radios and set them up
for radio in $WIFI_RADIOS ; do
echo " Multiple Radio Setup, Current Radio: $radio "
setup_mesh_radio $radio
done
else
echo " Calling Single Radio Setup: $WIFI_RADIOS "
setup_mesh_radio $WIFI_RADIOS
fi
} }
# This is called from the process_radios function and is passed the radio to be used for mesh # This is called from the process_radios function and is passed the radio to be used for mesh
@ -126,18 +318,12 @@ setup_mesh_radio() {
# Commit changes to wireless
# Commit changes to wireless
uci commit wireless
uci commit wireless
uci set network.nwi_mesh_$CURRENT_RADIO = interface
uci set wireless.mesh_$CURRENT_RADIO = 'wifi-iface'
uci set network.nwi_mesh_$CURRENT_RADIO .proto= 'batadv_hardif'
uci set wireless.mesh_$CURRENT_RADIO .device= " $CURRENT_RADIO "
uci set network.nwi_mesh_$CURRENT_RADIO .master= 'bat0'
uci set wireless.mesh_$CURRENT_RADIO .ifname= " mesh_ $CURRENT_RADIO "
uci set network.nwi_mesh_$CURRENT_RADIO .device= 'bat0'
uci set wireless.mesh_$CURRENT_RADIO .network= 'private_router_batman'
uci set network.nwi_mesh_$CURRENT_RADIO .mtu= '1536'
uci set wireless.mesh_$CURRENT_RADIO = wifi-iface
uci set wireless.mesh_$CURRENT_RADIO .device= $CURRENT_RADIO
uci set wireless.mesh_$CURRENT_RADIO .ifname= mesh_$CURRENT_RADIO
uci set wireless.mesh_$CURRENT_RADIO .network= nwi_mesh_$CURRENT_RADIO
uci set wireless.mesh_$CURRENT_RADIO .mode= 'mesh'
uci set wireless.mesh_$CURRENT_RADIO .mode= 'mesh'
uci set wireless.mesh_$CURRENT_RADIO .mesh_id= $MESH_NAME
uci set wireless.mesh_$CURRENT_RADIO .mesh_id= " $MESH_NAME "
uci set wireless.mesh_$CURRENT_RADIO .mesh_fwding= '0'
uci set wireless.mesh_$CURRENT_RADIO .mesh_fwding= '0'
uci set wireless.mesh_$CURRENT_RADIO .mesh_rssi_threshold= '0'
uci set wireless.mesh_$CURRENT_RADIO .mesh_rssi_threshold= '0'
uci set wireless.mesh_$CURRENT_RADIO .mesh_ttl= '1'
uci set wireless.mesh_$CURRENT_RADIO .mesh_ttl= '1'
@ -163,7 +349,6 @@ setup_mesh_radio() {
ENCRYPTION_ENABLED = $( uci -q get easymesh.config.encryption)
ENCRYPTION_ENABLED = $( uci -q get easymesh.config.encryption)
# Setup the interface for the mesh network
# Setup the interface for the mesh network
uci set wireless.mesh_$CURRENT_RADIO .disabled= '0'
uci set wireless.wifinet$RADIO_NUM = wifi-iface
uci set wireless.wifinet$RADIO_NUM = wifi-iface
uci set wireless.wifinet$RADIO_NUM .device= $CURRENT_RADIO
uci set wireless.wifinet$RADIO_NUM .device= $CURRENT_RADIO
uci set wireless.wifinet$RADIO_NUM .mode= 'ap'
uci set wireless.wifinet$RADIO_NUM .mode= 'ap'
@ -172,9 +357,16 @@ setup_mesh_radio() {
uci set wireless.wifinet$RADIO_NUM .mobility_domain= $MOBILITY_DOMAIN
uci set wireless.wifinet$RADIO_NUM .mobility_domain= $MOBILITY_DOMAIN
uci set wireless.wifinet$RADIO_NUM .ft_over_ds= '0'
uci set wireless.wifinet$RADIO_NUM .ft_over_ds= '0'
uci set wireless.wifinet$RADIO_NUM .ft_psk_generate_local= '0'
uci set wireless.wifinet$RADIO_NUM .ft_psk_generate_local= '0'
uci set wireless.wifinet$RADIO_NUM .network= 'lan'
uci set wireless.wifinet$RADIO_NUM .disabled= 0
uci set wireless.wifinet$RADIO_NUM .disabled= 0
# Check if ap_mode_enabled is enabled, if so add private_router_batman to the network
# otherwise just add lan
if [ " $( uci -q get easymesh.config.ap_mode_enabled) " = 1 ] ; then
uci set wireless.wifinet$RADIO_NUM .network= 'lan'
else
uci set wireless.wifinet$RADIO_NUM .network= 'lan private_router_batman'
fi
# Get the encryption key from the config
# Get the encryption key from the config
NETWORK_KEY = $( uci -q get easymesh.config.key)
NETWORK_KEY = $( uci -q get easymesh.config.key)
@ -213,22 +405,6 @@ setup_mesh_radio() {
uci commit wireless
uci commit wireless
fi
fi
# Check if we need to setup iapp
ENABLE_IAPP = $( uci -q get easymesh.config.iapp)
if [ " $ENABLE_IAPP " = 1 ] ; then
# Get the LAN interface name
LAN_NAME = $( uci -q get network.@device[ 0] .name)
# If LAN_NAME is not empty, set the iapp interface
if [ ! -z " $LAN_NAME " ] ; then
uci set wireless.wifinet$RADIO_NUM .iapp_interface= " $LAN_NAME "
uci commit wireless
fi
else
uci -q delete wireless.wifinet$RADIO_NUM .iapp_interface
uci commit wireless
fi
# If KVR is enabled, setup DAWN
# If KVR is enabled, setup DAWN
if [ " $ENABLE_KVR " = 1 ] ; then
if [ " $ENABLE_KVR " = 1 ] ; then
RSSI = $( uci -q get easymesh.config.rssi_val)
RSSI = $( uci -q get easymesh.config.rssi_val)
@ -246,207 +422,89 @@ setup_mesh_radio() {
} }
restart_and_reload( ) {
restart_and_reload( ) {
# Enable all the radios and commit the changes at once
# Get the radio to be used for mesh from the config
for radio in $( uci -X show wireless | grep wifi-device | awk -F'[.=]' '{print $2}' ) ; do
AP_RADIO = $( uci -q get easymesh.config.apRadio)
# Check if AP_RADIO is empty, if so exit
if [ -z " $AP_RADIO " ] ; then
echo "No radio specified in the config, exiting."
exit 1
fi
# Enable radios
for radio in $AP_RADIO ; do
echo " Enabling $radio ... "
echo " Enabling $radio ... "
uci set wireless.$radio .disabled= 0
uci set wireless.$radio .disabled= 0
done
done
uci commit
echo "All radios enabled."
# Apply the wireless configuration changes
uci commit wireless
wifi reload
# Reload wifi to apply changes without restarting all interfaces
wifi up
echo "Wireless interfaces reloaded."
echo "Wireless interfaces reloaded."
# Apply network configuration changes
# Apply network configuration changes
# Note: Only use reload_config if you have made changes to the network config
# and need to apply them. Otherwise, you can skip this step.
reload_config
reload_config
echo "Network configuration reloaded."
echo "Network configuration reloaded."
/etc/init.d/network reload
/etc/init.d/network reload
/etc/init.d/network restart
} }
disable_easymesh ( ) {
disable_batman_interfaces ( ) {
# Delete the bat0 interface
# Delete the bat0 interface
if [ " $( uci -q get network.bat0) " = "interface" ] ; then
if [ " $( uci -q get network.bat0) " = "interface" ] ; then
uci del network.bat0
uci del network.bat0
fi
fi
# Get the current list of ports for the 'br-lan' interface
# Delete the private_router_batman network interface
LAN_PORTS = $( uci -q get network.@device[ 0] .ports)
if [ " $( uci -q get network.private_router_batman) " = "interface" ] ; then
# Check if 'bat0' is already in the list of ports for 'br-lan'
uci del network.private_router_batman
if echo " $LAN_PORTS " | grep -q 'bat0' ; then
uci del_list network.@device[ 0] .ports= 'bat0'
echo "Old bat0 interface deleted from lan network."
fi
fi
# Get the list of wifi devices
uci commit network
WIFI_RADIOS = $( uci -X show wireless | awk -F'[.=]' '/wifi-device/ {print $2}' | tr '\n' ' ' )
# Loop through all the radios and delete the network interfaces
for CURRENT_RADIO in $WIFI_RADIOS ; do
echo " Handling removal of mesh networks for: $CURRENT_RADIO "
if [ " $( uci -q get network.nwi_mesh_$CURRENT_RADIO ) " = "interface" ] ; then
uci del network.nwi_mesh_$CURRENT_RADIO
uci commit network
fi
done
uci commit
reload_config
reload_config
echo "Network configuration reloaded."
/etc/init.d/network reload
/etc/init.d/network reload
/etc/init.d/network restart
echo "Network configuration reloaded."
} }
set_apmode( ) {
# Enable easymesh
AP_MODE = $( uci -q get easymesh.config.ap_mode)
enable_easymesh( ) {
if [ " $AP_MODE " = 1 ] ; then
# Clear old radios then set "old values"
# Set a flag to indicate that we are in AP mode
clear_by_mesh_id " $( uci -q get easymesh.config.mesh_id) "
# When we go to disable easymesh, we will check this flag and if it was set we restore settings
clear_by_mesh_id " $( uci -q get easymesh.config.old_mesh_id) "
uci set easymesh.config.ap_mode_enabled= 1
uci set easymesh.config.old_mesh_id= " $( uci -q get easymesh.config.mesh_id) "
create_batman_network
# Backup our configs
process_radios
rm /etc/config/*.meshbak
restart_and_reload
cp /etc/config/wireless /etc/config/wireless.meshbak
# Set at end to be sure it worked
cp /etc/config/network /etc/config/network.meshbak
uci set easymesh.config.running= 1
cp /etc/config/dhcp /etc/config/dhcp.meshbak
}
# Generate a random IP in the same subnet for fun
# ip_base=$(echo "$dns" | cut -d'.' -f1-3) # Get the first three octets of the DNS IP
# last_octet=$((RANDOM % 254 + 1)) # Generate a random value for the last octet between 1 and 254
# nodeip="${ip_base}.${last_octet}" # Concatenate the base IP with the new last octet
# Disabling and stopping services not needed
for service in firewall dnsmasq odhcpd; do
if /etc/init.d/$service enabled; then
echo " Disabling and stopping $service ... "
/etc/init.d/$service disable
/etc/init.d/$service stop
else
echo " $service is not enabled, skipping... "
fi
done
# Set LAN interface to DHCP client
uci del network.lan.ipaddr
uci del network.lan.netmask
uci set network.lan.proto= 'dhcp'
uci del network.wan
uci del network.wan6
# Fix firewall to be disabled
uci del firewall.lan.network
uci del firewall.wan.network
# Fix dhcp to be disabled
uci set dhcp.lan.ignore= '1'
uci del dhcp.wan
# Fix this for proper variable name
HOSTNAME = $( uci -q get easymesh.config.gateway)
# Set netmask and gateway (assuming $netmask and $dns didn't break more stuff)
uci set system.@system[ 0] .hostname= $HOSTNAME
# Retrieve the list of ports for network.@device[0]
LAN_PORTS = $( uci get network.@device[ 0] .ports)
# Check if 'wan' is already in the list of ports
if echo " $LAN_PORTS " | grep -q -w 'wan' ; then
echo "'wan' is already in the list of ports for lan."
else
echo "'wan' is not in the list. Adding it to lan ports..."
uci add_list network.@device[ 0] .ports= 'wan'
fi
# Find all radios we are using in our setup
find_radios
#### COME BACK TO THIS ####
# # Check if WIFI_RADIOS contains more than one radio
# if [[ $WIFI_RADIOS =~ [[:space:]] ]]; then
# # Loop through all the radios add nwimesh to the that network
# for cur_radio in $WIFI_RADIOS; do
# echo "Multiple Radio Setup, Current Radio: $radio"
# # Extact the radio number from the radio name
# wifi_num="${cur_radio#radio}"
# uci set wireless.wifinet${wifi_num}.network="lan nwi_mesh_${cur_radio}"
# done
# else
# echo "Calling Single Radio Setup: $WIFI_RADIOS"
# # Extact the radio number from the radio name
# wifi_num="${WIFI_RADIOS#radio}"
# uci set wireless.wifinet${wifi_num}.network="lan nwi_mesh_${WIFI_RADIOS}"
# fi
uci commit
# Tell openwrt to reload the configs
reload_config
else
# Set a flag to indicate that we are in AP mode
uci set easymesh.config.ap_mode_enabled= 0
# Restore our configs
[ -f /etc/config/wireless.meshbak ] && {
mv /etc/config/wireless /etc/config/wireless.dumbap
cp /etc/config/wireless.meshbak /etc/config/wireless
}
[ -f /etc/config/network.meshbak ] && {
mv /etc/config/network /etc/config/network.dumbap
cp /etc/config/network.meshbak /etc/config/network
}
[ -f /etc/config/dhcp.meshbak ] && {
mv /etc/config/dhcp /etc/config/dhcp.dumbap
cp /etc/config/dhcp.meshbak /etc/config/dhcp
}
# Enable and start services not needed
for service in firewall dnsmasq odhcpd; do
if /etc/init.d/$service disabled; then
echo " Enabling and starting $service ... "
/etc/init.d/$service enable
/etc/init.d/$service start
else
echo " $service is not disabled, skipping... "
fi
done
reload_config
# Disable easymesh
/etc/init.d/network reload
disable_easymesh( ) {
fi
# Clear old radios then set "old values"
clear_by_mesh_id " $( uci -q get easymesh.config.mesh_id) "
clear_by_mesh_id " $( uci -q get easymesh.config.old_mesh_id) "
uci del easymesh.config.old_mesh_id
disable_batman_interfaces
# Set at end to be sure it worked
uci del easymesh.config.running
} }
# ENABLED=$(uci -q get easymesh.config.enabled) if [ " $1 " = "enable" ] ; then
# if [ "$ENABLED" = 1 ]; then enable_easymesh
# clear_old_networks exit 0
# create_bat0 elif [ " $1 " = "disable" ] ; then
# find_radios
# process_radios
# restart_and_reload
# else
# clear_old_networks
# disable_easymesh
# fi
# We accept the parameters: start, stop and apmode
# start: Enables easymesh
# stop: Disables easymesh
# apmode: Sets the device to AP mode
if [ " $1 " = "start" ] ; then
clear_old_networks
create_bat0
find_radios
process_radios
restart_and_reload
elif [ " $1 " = "stop" ] ; then
clear_old_networks
disable_easymesh
disable_easymesh
# elif [ "$1" = "apmode" ]; then exit 0
# set_apmode elif [ " $1 " = "dumbap" ] ; then
set_apmode
exit 0
elif [ " $1 " = "undumb" ] ; then
disable_apmode
exit 0
else else
echo "Invalid parameter passed."
echo "Invalid argument. Please use 'start', 'stop' or 'dumbap'"
exit 1
fi fi
Jason Hawks
10 months ago